Blue-ox BX88273 Manuale Utente Scaricare il pdf

BX88273

2 ATM Fuse ByPass Switch

Installation Instructions

405-0240 Rev A Page 1 of 2 7/30/13

ALWAYS match the amperage of the fuse in the Fuse ByPass Switch harness to the fuse removed

from the fuse panel.

NEVER install a fuse with more than a 20 amp rating in the Fuse

ByPass Switch harness.

REMOVE any fuse from the Fuse ByPass Switch harness.

BEFORE YOU BEGIN: Consult the owner’s manual for the

towed vehicle to determine which fuse must be removed from

the “towed” vehicle. Conrm that the pins on the Fuse ByPass Switch wires match the pin sizes on

the fuse you removed. You must have the correct fuse wire ends for your fuse box. If your vehicle is

equipped with a ATM Micro Mini fuse, a ATM Mini fuse of the same rating as the OEM will need to be

installed into the ATM Mini Fuse Bypass Switch holder.

Follow each of the steps below for each circuit:

1. Install the two (2) small wire pins of one (1) pair of wires into the fuse panel location from where

you removed the fuse in the “towed”. Press in on the pins until fully seated. (There is a “Red” pair

and “Black” pair of wires indicated by the color of heatshrink at the pin ends)

Note: On Honda vehicles you will need to press the wire pins to the outside edges of the fuse

opening since these panels have the connectors on the sides of the opening, not at the bottom.

Insure that fuse panel cover can be replaced. If necessary use wire ties (not supplied) to hold the

wiring rmly in place insuring a rm physical and electrical connection.

2. Find a suitable location on a plastic surface (1/4” thick or less) next to the fuse box to mount the

Fuse ByPass. It is highly recommend that installation is on the outer, removable panel used to

access the fuse panel.

Conrm that there is ample space for the switch and that there is no metal behind the area you

have chosen. Be sure that you can reach the back of the Fuse ByPass in order to install the

mounting nut and to reattach the wires.

Note: On 2007 Honda CRV’s, the switch might be mounted on the side of the dash area coin

holder; on newer CRV’s install the Fuse ByPass on the lower dash tray.

3. Carefully drill a 3/4” diameter hole into the plastic panel using a at power auger. Avoid drilling into

or damaging any nearby wiring.

4. Remove the 4 wires from the switch by carefully and rmly pulling on the connectors one at a time.

5. Place the switch into the hole, install the mounting nut with the serrated side towards the panel

and hand tighten it.

6. Reattach the wires to the switch by sliding the connectors over the terminals on the switch.

7. Slide the black split loom over the wiring connections and if necessary, secure with electrical tape.

1 2

Sommario

Pagina 1 - Installation Instructions

BX882732 ATM Fuse ByPass SwitchInstallation Instructions405-0240 Rev A Page 1 of 2 7/30/13ALWAYS match the amperage of the fuse in the Fuse ByPass S

Pagina 2

BX882732 ATM Fuse ByPass SwitchInstallation Instructions405-0240 Rev A Page 2 of 2 7/30/138. Tape the wiring if there is any exposed metal in the i

Commenti su questo manuale

Nessun commento

Blue-ox BX88273 Manuale Utente

Navigare online o scaricare Manuale Utente per Per l'auto Blue-ox BX88273. Blue Ox BX88273 User Manual Manuale Utente

Sommario

Commenti su questo manuale

Prodotti e manuali riguardandi Per l'auto Blue-ox BX88273